Viessmann Vitola 200 Instruções de Operação

Service instructionsfor heating engineersVitoflame 200Oil pressure jet burner (type VEK)H up to 40 kW with oil pre-heaterH from 50 kW without oil pre-

Initial start-up and maintenance10Implementation(Cont.)11. Nozzle replacementMaintenance1. Plug the burner chassis withnozzle assembly pointing upward

Initial start-up and maintenance11Implementation(Cont.)12. Checking and adjusting the ignition electrodesMaintenance15 to 33 kW40 to 63 kWCheck igniti

Initial start-up and maintenance12Implementation(Cont.)14. Cleaning or, if necessary, replacing the oil pump filterMaintenanceDanfoss oil pumptype BFP

Initial start-up and maintenance13Implementation(Cont.)16. System start-upMaintenance1. Open the oil filter valve.2. Switch on the mains electricaliso

Initial start-up and maintenance14Burner control unitYou may use the following burnercontrol units with this burner:Burner control unit LOA 14.171B2VH

Initial start-up and maintenance15Burner control unit(Cont.)Burner control unit LMO 14.113A2 (Cont.)H OperationThe reset button ET isthe central contr

Initial start-up and maintenance16Burner control unit(Cont.)Burner control unit LMO 14.113A2 (Cont.)H Fault cause diagnosisThe red signal lamp stays o

Initial start-up and maintenance17Burner control unit(Cont.)Burner control unit LMO 14.113A2 (Cont.)During the fault cause diagnosis, all control outp

Troubleshooting18Procedure overviewDiagnosis 1. Establish fault/ascertain system behaviour.2. Look for the corresponding fault cause in the diagnosis

Troubleshooting19DiagnosisFault/behaviour of the system Cause of fault CheckBurner does not start (without faultdisplay), fault lamp does notilluminat

General Information2Safety instructionsPlease follow these safety instructions closely to avoid the risk of injury to individuals and damage to proper

Troubleshooting20Diagnosis(Cont.)Fault/behaviour of the systemCause of fault CheckBurner starts up and flame isFlame monitor contaminated. Clean the f

Additional information21SpecificationRated output kW 15 18 22 27 33 40 50 63Type of burner VEKI-1 VEKI-1 VEKI-1 VEKI-1 VEKI-1 VEKI-2 VEKII-1 VEKII-2Ty

Additional information22Approximate values for burner settingsPlease note:Check whether the service instructions are valid for the boiler concerned (s

23Platzhalter Bauteilübersicht5692 437 GB

24PPPPllllaaaattttzzzzhhhhaaaalllltttteeeerrrr5692 437 GB

25PPPPllllaaaattttzzzzhhhhaaaalllltttteeeerrrrSSSSttttrrrroooommmmllllaaaauuuuffffppppllllaaaannnn5692 437 GB

26PPPPllllaaaattttzzzzhhhhaaaalllltttteeeerrrr5692 437 GB

27PPPPllllaaaattttzzzzhhhhaaaalllltttteeeerrrrEEEEiiiinnnnzzzzeeeelllltttteeeeiiiilllllllliiiisssstttteeee5692 437 GB

28PPPPllllaaaattttzzzzhhhhaaaalllltttteeeerrrr5692 437 GB

29PPPPllllaaaattttzzzzhhhhaaaalllltttteeeerrrr5692 437 GB

Contents3PageGeneral informationSafety instructions 2...Appli

30PPPPllllaaaattttzzzzhhhhaaaalllltttteeeerrrr5692 437 GB

Additional information31Maintenance ReportMaintenance/ServiceDate:By:Maintenance/ServiceDate:By:Maintenance/ServiceDate:By:Maintenance/ServiceDate:By:

Viessmann Werke GmbH&CoD-35107 AllendorfTel: (06452) 70-0Fax: (06452) 70-2780www.viessmann.deViessmann LimitedHortonwood 32, TelfordShropshire, TF

Additional informationComponent overview23/245692 437 GBA Air regulating valveB Flame monitor(flicker detector)C Burner control unitD Reset buttonE Co

Additional informationWiring diagramLegendA‘ Start of oil pre-heat timeAStart-upB Timing of flamebeing establishedC Operating positionD Controlled shu

Additional informationParts listWhen ordering spare parts:Quote the type and serial no. (seetype plate) and the item no. of therequired part (as per p

Additional informationParts list(Cont.)Parts019 Impeller020 Oil hose - flow021 Oil hose - return027 Sensor plate030 Nozzle assembly with oilpre-heater

Initial start-up and maintenance4Procedure overviewInitial start-up stepsMaintenance stepsI1. System start-up Page 5...

Initial start-up and maintenance5ImplementationTo obtain the optimum combustion values, it is essential to adjust the burnerwith the boiler heated to

Initial start-up and maintenance6Implementation(Cont.)Initial start-up2. Oil pressure adjustment and vacuum checkMaintenancePlease note:The oil pressu

Initial start-up and maintenance7Implementation(Cont.)Initial start-up3. Air volume fine adjustmentMaintenancePlease note:The oil pressure is preset a

Initial start-up and maintenance8Implementation(Cont.)Initial start-up4. Burner checkMaintenanceRecord all test values in the order ofthe maintenance

Initial start-up and maintenance9Implementation(Cont.)8. Cleaning the burnerMaintenance1. Set the burner to maintenance.2. Clean the housing and the b